NETWORK TOPOLOGY

What is Topology 

Network Topology is the arrangement of the various elements links, nodes, etc. of a computer network. it is the topological structure of a network and may be depicted physically or logically.
Topologies are divided into two types. One is called physical topology & another one is logical topology.
Physical topology is the placement of the various components of a network, including device location and cable installation, while logical topology illustrates how data flows within a network, regardless of its physical design.
Distances between nodes, physical interconnections, transmission rates, or signal types may differ between two networks.
 Topology


There are a number of reasons to understand about Topology:

  • The network topology impacts performance
  • The network topology is a factor in determining the media type used to cable the network
  • The networking topology impacts the cost of cabling the network.
  • Some access methods works only with specific topologies

Types Of Topologies

There are 6 different types of physical Topologies.
  1. Bus topology
  2. Ring topology
  3. Star topology
  4. Mesh topology
  5. Tree topology
  6. Hybrid topology

BUS TOPOLOGY :

Bus Topology is a network where all the nodes are connected with each Other with a single common cable. When one node wants to access another node on the network then it puts a message addressed to that device on the bus.
Bus Topology

Advantages of BUS Network:


         1 .   It is very easy to connect a node or peripheral in this network.
2.   Bus network requires less cable length than any other topologies.
Disadvantages of BUS Network:
1.  As the total network is depended on a single cable so if any problem occurs in the main cable, the entire network shuts down.
2.  At the start & the end point of the main cable terminators are required to build up the network.
3.  This network cannot be used as a stand-alone solution in a large building.

RING TOPOLOGY:

When each device is serially connected in a closed ring pattern with a single cable then the network system is called ring topology. As a train crosses all the platforms to reach its destination, ring topology does the same to pass a message from one node to another node.
Ring Topology


Advantages of ring Topology:

1.   The network don't do anything without order. It needs to access the token the opportunity to transmit.
2.    In this network each & every node has equal access to resources. 
3.    The performance does not get interrupted by any additional components.
  4.     Network server is not needed to control the connection between nodes.

Disadvantages of ring Topology:
1.   In this ring network if any node breaks down then the entire network System stops working.
2.  The speed of transferring data is slower than any other topologies just because a packet of data passes through all the nodes between sender & receiver node
3.  The entire network could be affected by moving, adding & changing of devices.

 STAR TOPOLOGY:

In this configuration all nodes are connected to a central Hub with separated cables. Here the central node or hub acts like the main server & the other nodes which are connected to the central node, act like client devices.
Star Topology

Advantages of star topology:

  • In this type of network, it is very easy to add or remove a node to the network
  • Here if any fault occurs it is very easy to find out & fix it up
  • If anyone node faces problem, the rest nodes perform smoothly without


Disadvantages of star Topology:
  •  It is more expensive than any other topologies to build up the network because it requires excessive length of cable.
  • The entire network goes down if the central node does not work properly & also if the other important nodes are disconnected from the network, example file server node stops working
  • The central hub is expensive which makes the network more expensive.

MESH TOPOLOGY:

Here each & every network is interconnected with each other. It works independently.
Mesh Topology

Advantages of Mesh Topology:

1.      Adding or removing nodes in this network could be done easily without interrupting the other nodes & the network.
2.   Here the transmission of data is very easy because it transfers data from different nodes simultaneously.
3.    In this configuration transfer of data does not get affected by any peripherals because if one node fails there is always an alternative one.

Disadvantages of Mesh Topology:

1. It is very hard to configure the network & also very difficult to maintain.
2. Mesh topology is comparatively expensive when compared with other topologies like ring or star topology.

TREE TOPOLOGY:

A tree topology looks like the branches of the tree where each & every nodes are connected with its parent's node. It is also called by the name star+bus topology.
Tree Topology


Advantages of tree topology:
1.   Here finding out any fault is very easy & not too hard to maintain.
2.   If one of the any nodes get damaged the other hierarchical nodes are not affected.
3.   It is very easy to extend the network as much as administrator wants. 
Disadvantages of tree topology:
1.    The network requires high maintenance.
2.   A lot of cable is required to establish the network system.Troubleshooting of problems is highly difficult.


HYBRID TOPOLOGY:

Hybrid topology is the combination of two or more different network topologies
This network is a mixture of both peer-to-peer & client-server network. ft can be either wired or wireless network.
Hybrid Topology

Advantages of hybrid topology:
1. Here in this network the troubleshooting is far better than any other topologies.
2. This type of network is very easy to expand.
Disadvantages of hybrid topology:
1 .  The structure of the network is hard to understand.
2.It is very expensive to build up the entire network because of the requirement of cables & other peripherals.
      3.   Multi-station Access Unit is required.

Comments

Post a Comment

Popular posts from this blog

WIRELESS NETWORKING

Image
Wireless Networks Wireless networks are computer network that are not connected by cables of any kind In simple words. when two or more devices are connected without any networking cable, It is called wireless networking. From cell phone, to simple home wireless internet connection, Bluetooth and more, everything comes under wireless networking. Wireless Networks: Ir DA: Infrared Data Association Data Association has developed a standard where data is transmitted via Infrared light waves It is a protocol where beams are used in the Infrared light s spectrum. In case of Ir DA, as the data transfer is done through infrared, you can send data to one device at a time.   Bluetooth: Bluetooth uses 2.45 gigahertz radio waves to share data between devices. The technology is limited to a short distance of 10 ft but it can cross walls in order to transmit data This also communicates without wire. The figure shows the various Bluetooth versions. Home RF: Horn
Read more

Broad network categories

Image
Broad network categories There are two broad network categories, 1) Peer-To-Peer(P2P) Networks   -   Peer-To-Peer networks involve two or more  computers pooling individual resources such as disk drives. Each computer acts as both the client and the server, These computers can directly communicate with the other computers. On a peer-to-peer network, for example, a scanner on one computer can be used by any other computer on the network. P2P networks are cheap to set up. Its connection type can be by using Ethernet cable or a Wi-Fi router. 2)  Client-Server Networks -  This involves multiple client networks which are connected to at least a central server on network where, applications are installed.        Clients need access to these server resources, they can access them only from the server. Servers often have private user directories for special users (Example, Windows has Work folders for Special users). Client-server networks tend to have faster access spe
Read more

Internet Protocol (IP)

Internet Protocol (IP) An IP address is a unique address used to identify each devices (computer,mobile,printers) connected to an IP Network IPv4 internet protocol version 4 is currently the most used address in standard on the other hand IPv6 is also being used widely.  An IPv4 address contains 32 bit binary number as it is difficult to two people to work with the binary numbers that computer uses IP addresses are converted into decimal format before they are displayed this makes the whole process faster and more reliable - An IP address is a unique address used to identify each device connected to an IP Network.  - 32 bit IPv4 is most widely used while 128 bit why IPv6 is gradually taking over.  - IPv4 uses decimal format and IPv6 uses hexadecimal format. - In networking, IP is a base of networking or CCNA IP Classes The internet protocol or IPv4 system is divided into five classes, Each class is created to accommodate a network of a specific siz
Read more